No products in the cart.
-
Yucel Y2.1-12 Batteries
- 12V 2.1Ah Yucel SLA Battery
- Three year design life
- 1 Year Warranty
- Yucel Y2.1-12 Batteries data sheet
£6.72 Inc VAT -
Hochiki YBN-R/3(WHI) Addressable/Analogue Detection
- Electronics free
- Slim profile – only 8 mm
- Rugged stainless steel wiring contacts
- Facility for remote indicator
- 3 year warranty
- Hochiki YBN-R/3(WHI) Addressable/Analogue Detection instruction
- Hochiki YBN-R/3(WHI) Addressable/Analogue Detection data sheet
£1.72 Inc VAT -
Fulleon 540503FULL-0403X Horns (Sounders)
- Deep base, red
- 102dBA
- IP65
- 32 tones (user selectable)
- 9-28Vdc
- 12mA
- EN54-3
- 1-year warranty
- datasheet
£15.14 Inc VAT -
Elmdene STX2410-E Power Management
- Elmdene’s new STX range of high quality, cost effective EN54-4, 3rd party certified power supplies are designed specifically for Fire applications
- Available in 24V dc 1A, 2A, 5A and 10A power variants in a choice of enclosures they are capable of providing support for different standby battery configurations required by the installation
- 27.6V dc output
- Cost effective switch mode technology
- Energy efficient
- Intelligent battery charging and monitoring using Elmdene’s EcoCharge technology
- Deep Discharge Protection
- Remote fault signalling
- 3 Year Warranty
- Elmdene STX2410-E Power Management data sheet
£232.99 Inc VAT -
Hochiki ALN-EN(WHT) Addressable/Analogue Detection
- Removable, High Performance chamber
- Twin LEDs allow 360deg viewing – green when polling, turn red in fire
- Electronically addressed
- Pulsing/non-pulsing controlled from panel
- EN54-7
- 3 year warranty
- Hochiki ALN-EN(WHT) Addressable/Analogue Detection data sheet
£26.38 Inc VAT -
Apollo SA7100-100APO Addressable/Analogue Detection
- Intelligent Auto-Aligning Beam Detector
- Operating range 8-50 Metres
- Compatible with Discovery andXP95 protocols
- Drift compensation
- Integral laser and auto- align enable quicker installation
- Alignment compensation for building movement
- Low-level systemcontroller with LCD display and user friendly interface
- EN54-12/17
- 10 year warranty
- Apollo SA7100-100APO Addressable/Analogue Detection data sheet
- Apollo SA7100-100APO Addressable/Analogue Detection installation guide
£383.57 Inc VAT -
Fulleon 540501FULL-0389X Horns (Sounders)
- Voltage 9-15Vdc 18-28Vdc
- Current 12mA (Typical Tone 3)
- Sound Output 102dB(A) (Typical Tone 3)
Tones 32 - Volume Control 10dB
- Monitoring Reverse polarity
- Temperature – 25ºC to + 70ºC
- Protection IP54 (s)* IP65 (d)*
- Construction ABS
- Weight 0.25Kg
- Colours Red
- Shallow base red
- 1 year warranty
- data sheet
£15.14 Inc VAT -
Ventcroft VFP-215ERH Wire & Cable
- : Unscreened
- : 2Core
- : –
- : 1.5mm²
- : 328ft
- : 100m
- : Red
- : 2 x 1.5mm
- : Copper
- : LSZH
- : 8.1mm
- : 500V
- : 2C Series
- Ventcroft VFP-215ERH Wire & Cable data sheet
£79.66 Inc VAT - : Unscreened
-
Xpander XPA-MC-14006-APO Pull Stations/Manual Call Points
- Brand Apollo
- XPERT card addressing
- Resettable element
- Fast response (reports alarm condition in under one second)
- LED operation indicator
- 5 year battery life (using standard AA alkaline batteries)
- Certified to EN54-25
- 10 year warranty
- Xpander XPA-MC-14006-APO Pull Stations/Manual Call Points data sheet
£210.77 Inc VAT -
C-Tec XFP502/X Fire Control Panels
- Third-party certified to EN54-2/4 by the Loss Prevention Certification Board (LPCB).
- Compatibility with Apollo’s XP95/Discovery protocol.
- Two independently programmable conventional sounder circuits.
- Two programmable inputs.
- A fault output relay and three programmable relay outputs with voltage free changeover contacts.
- A selection of zone dependency/coincidence functions.
- A day/night (building occupied/unoccupied) function.
- An investigation delay period function.
- Phased evacuation facility.
- An alarm counter that records how many times the panel has been in alarm state.
- Powerful short circuit protected loop drivers, capable of supporting up to 40 loop powered 10mA sounders per loop.
- An integral EN54-4/A2 switch mode power supply.
- Adjustable contamination levels.
- Earth fault monitoring.
- Combined keypad / keyswitch entry to Access Levels 2 and 3.
- 999 event monitoring.
- An intuitive Windows based upload-download PC program.
- Optional flush-mounting bezel and glazed stainless steel enclosure also available.
- Up to eight XFP main panels (any variant) can be connected onto a two-wire RS485 network. Alternatively, up to eight XFP repeaters can be connected to any non-networked main panel.
- 1 year warranty
- C-Tec XFP502/X Fire Control Panels data sheet
£663.64 Inc VAT -
Kentec KL11020M2 Fire Control Panels
- Construction 1.2mm mild sheet steel
- IP Rating IP30
- Finish Epoxy powder coated
- Colour – lid & box BS 00 A 05 grey – fine texture
- Colour – control panel & labels RAL 7047 light grey – satin
- Weight 6kg
- Supply Voltage 230V AC (+10%/-15%)
- Mains supply fuse 1.6 Amp 250V
- Power supply DC rating 24V 3 Amps
- Maximum battery size 7Ah 12V (2 per panel)
- Fault contract rating 30V DC 1 Amp
- Local fire contract rating 30V DC 1 Amp
- Fire contract rating 30V DC 1 Amp
- Sounder output rating 0.5A per output (max 1.6A over all outputs)
- Detection zone current 1.6 milliamps
- Detection zone EOL resistor 6k8 5%
- Active EOL K14606K (optional)
- Sounder output EOL resistor 10k 5%
- Cable capacity 2.5mm² per terminal
- Operating temperature -5°C to +40°C
- Operating humidity <95% (non condensing)
- 3 Year Warranty
- Kentec KL11020M2 Fire Control Panels data sheet
£164.69 Inc VAT -
Advanced Electronics MX-5802 Fire Control Panels
- Base Technology Dual flash-based processors with real-time clock, trace diagnostics, programmable languages and character
sets - Display White backlit 240 x 64 graphical LCD
- LED Indicators 22 red (1 x Fire, 1 x More Alarms, 20 x Zonal Programmable), 1 green (Power), 13 amber and 7 bi-colour
(Fault & System) - Controls Alpha numeric keypad permitting Navigation, Reset, Mute, Silence, Resound, Evacuate, and 4 x
Programmable Push ButtonsActual 2 - Protocols Apollo (Xp95 / Discovery), Hochiki ESP, Argus Vega and Nittan Evolution
- Number of Fire Zones 2000 when networked (400 max across 8 loops)
- Number of loops Dedicated 2-8 loop control panel
- Devices per loop Protocol dependent
- Loop Current 500mA max per loop
- On-Board Sounder Circuits 8 x 1 Amp programmable
- On-Board Relays 4 x 1 Amp 30v AC/DC programmable (10mA, 5v min) – expandable to 8 using 2 x Mxp-507
- Auxiliary Supply 2 x 24v 500mA 2
- Programmable Input 2 x On-board Programmable Input
- Programmable Key Switch Inputs 16 volt free digital inputs
- Total Available Output Current 2 x 5A maximum available for loop current + sounder outputs + auxiliary supply
- Mains Supply 200 – 240v 47-63 Hz AC (+10%, -15% tolerance) 1.4A max
- Battery Capacity 2 x 24V 4Ah internal (min), 2 x 24V, 18Ah internal (max), or 1 x 24V 45Ah internal (max) and 1 x 24V 45Ah external (max) using optional battery enclosure
- Charger Current 2 x 2.0A temperature compensated
- Serial ports 2 x on-board RS232 connection for PC, modem, IP or portable printer
- USB Interface 2 x USB B type connection for PC communication
- Programming On-board keypad or PC running Windows tools
- Event Log 2 x 5000 Event & Diagnostic + 500 Fire
Printer (Optional) On-board - Enclosure / Colour Steel IP30 / RAL7035
- Cable Entry (20mm knockouts) 30 x top, 6 x rear, 3 x bottom plus 2 x double knockout rear
- Size H x W x D mm 750 x 450 x 190
Metalwork Options Flushing bezel, battery box, utility enclosure, termination enclosure and rack mount - 3 year warranty
- Advanced Electronics MX-5802 Fire Control Panels data sheet
£4,354.73 Inc VAT - Base Technology Dual flash-based processors with real-time clock, trace diagnostics, programmable languages and character
-
KAC K21SRS-01 Pull Stations/Manual Call Points
- Key captive in one position
- Indoor
- Plain
- Variety of keyswitch devices avaialable
- Suitable for Fire, Security & Other Specialist
Applications - Variety of colours and markings
- 3 Year warranty
- • Variety of keyswitch devices avaialable
Suitable for Fire, Security & Other Specialist
Applications - Variety of colours and markings data sheet
£20.30 Inc VAT -
C-Tec ECU-8 Voice Evacuation Alarms
- Approvals/certifications Facilitate compliance with BS5839-9 when correctly installed
- Mains supply 230V 50/60Hz.
- Mains rated current500mA.
- Internal power supply 19V-28.5V (27V nominal). Ripple 7V maximum (battery fault).
- Total output current limited to1.5A @ 230Vac Quiescent current100mA (controller with fault buzzer sounding) plus 1mA per Type A outstation and 3.2mA per Type B outstation.
- Max battery size and type2 x 12V 7Ah VRLA connected in series.
- No. of lines8.Auxiliary relay changeover fault relay (failsafe). 30V 1A max
- Open collector outputs(OP1): Activates when the ECU is ringing; (OP2) Activates when there is an active accessible toilet alarm call; (OP3) Closes when the handset is off-hook and remains active for 2 mins after it is replaced. 24V, 50mA max.
- Other outputs +24 V.
- Typically used to supply power to equipment connected to the ECU’s open-collector outputs (relays, etc). Engineer (AL3) functions Engineer mode and reset buttons (internal).
- Indicators 128 x 64 pixel LCD display; Disablement; System fault; PSU fault; General fault; Power on.
- ControlsSilence Buzzer.
- Other controls are available but are not applicable as no handset is provided on this unit.
- Product dimensions (mm)410 W x 250 H x 80 D mm (base); 439 W x 274 H x 7 D mm (lid).
- Construction & finish metal lid and base, RAL7035 grey texture.
- IP Rating IP20.
- Weight 3.1kg (without batteries).
- Operating conditions/temperature-5ºC to +40ºC. Max relative humidity: 95%.
- 1 year warranty
- C-Tec ECU-8 Voice Evacuation Alarms data sheet
£915.94 Inc VAT -
Advanced Electronics MXM-521
- product Dimensions: H220mm x W300mm
- Semi-flush fitting for all MxPro5 panels
- Picture frame effect for ease of installation 30mm flange for control panels, 20mm for repeaters
- Fitting kit included
- Advanced Electronics MXM-521 data sheet
£62.33 Inc VAT -
Advanced Electronics MXP-013-100
- 100 zones available
- Cost beneficial against ancillary hardware
- Factory fitted or retro fit
- Dynamic zoning
£421.32 Inc VAT -
Ventcroft VFP-225ERH Wire & Cable
- 2 Cores and Earth 2.50mm
- Red
- Brand No Burn
- Weight 9.5 kg
- Conductor Material Copper
- 100m Reel
- Ventcroft VFP-225ERH Wire & Cable data sheet download
£140.51 Inc VAT -
Advanced Electronics MX-5401/D Fire Control Panels
- 20 programmable Zonal / 25 System LEDs.
- Apollo, Argus Vega, Hochiki & Nittan Evolution* protocol support.
- Advanced graphical LCD user interface and support for up to 200 fire zones by default allowing full EN54 compliance without additional hardware.
- Dedicated USB & RS232 serial port for direct PC or modem connection.
- Installer friendly Auto-learn, Loop Detection and On-board Scope facility for ease of commissioning and fault finding.
- The graphical display can be configured to operate with virtually any language or character set, and allow the installer’s logo to be applied using the Logo application software.
- Integral P-Bus for system expansion via available option cards.
- Ad-NeT peer-to-peer network with up to 2000 zones
- Approved to BS EN54 part 2, 4 and 13.
- 3 year warranty
- Advanced Electronics MX-5401/D Fire Control Panels data sheet
£1,844.65 Inc VAT -
Kentec K11040M2 Fire Control Panels
- Fully certified to BS EN54-2 and BS EN54-4
- 2-wire and standard versions in 2, 4 or 8 zones
- Compatible for use on BS5839: Part 1: 2002 installations
- 2-wire repeaters and ancillary boards
- Simple, single board construction
- Installer friendly
- Compatible with wide range of detection devices
- Two monitored sounder outputs
- 3 Amp power supply
- Auxiliary power output
- 3 year warranty
- Kentec K11040M2 Fire Control Panels data sheet
£183.86 Inc VAT -
Fike 402-0006 Pull Stations/Manual Call Points
- Re-settable element
- Reset key
- Back box and adaptor plate for flush mount
- 18-35Vdc
- 2 year warranty
- Fike 402-0006 Pull Stations/Manual Call Points reset key data sheet
£28.78 Inc VAT -
Ventcroft VFP-210EWH Wire & Cable
- 2 Cores and Earth 1.00mm
- White
- noburn
- 100m Reel
- Ventcroft VFP-210EWH Wire & Cable data sheet
£76.78 Inc VAT -
CQR FP3/RD Pull Stations/Manual Call Points
- Surface or flush mounted
- Frangible and resettable windows
- 470 or 680ohm resistor settings
- EN54-11
- Single change over
- Resettable or non-resettable
- Available in red, green or white
- High visibility LED
- Red is CPR and EN54-11 approved
- 2 year warranty
- CQR FP3/RD Pull Stations/Manual Call Points data sheet
- CQR FP3/RD Pull Stations/Manual Call Points user manual
£7.80 Inc VAT -
Kentec T11080M2 Fire Control Panels
- 0.093Amp Standby
- 385 x 310x 90mm
- Two-wire and standard versions in two, four or eight
zones - Compatible for use on BS5839: Part 1: 2017
- installations
- Two-wire repeaters and ancillary boards
- Simple, single board construction
- Compatible with wide range of detection devices
- Two monitored sounder outputs
- Three Amp power supply
- Auxiliary power output
- Fully certified to BS EN54-2 and BS EN54-4
- 3 year warranty
- Kentec T11080M2 Fire Control Panels data sheet
£229.80 Inc VAT -
Kentec T11020M2 Fire Control Panels
- Construction : 1.2 mm mild sheet steel
- Finish : Epoxy powder coated
- Colour – lid & box : BS 00 A 05 grey – fine texture
- Colour – control plate & labels : RAL 7047 light grey – satin
- Supply voltage : 230 VAC (+10%/-15%)
- Mains supply fuse : 1.6 A 250V
- Power supply DC rating : 24V 3A
- Maximum battery size : 7Ah 12V (2 per panel)
- Fault contact rating : 30 VDC 1A
- Local fire contact rating : 30 VDC 1A
- Fire contact rating : 30 VDC 1A
- Sounder output rating : 0.5A per output (Max 1.6A over all outputs)
- Detection zone current : 1.6 mA
- Detection zone EOL resistor : 6K8 5%
- Active EOL : K14606K (optional)
- Sounder output EOL resistor : 10K 5%
- Cable capacity : 2.5 mm©
- Operating temperature : -5°C a +50°C
- Operating humidity : < 95% (non condensing)
- Dimension : 385 mm x 310 mm x 90 mm
- Standby current 2 zones : 0.065 A
- Standby current 4 zones : 0.075 A
- Standby current 8 zones : 0.093 A
- Alarm current 2 zones : 0.15 A
- Alarm current 4 zones : 0.30 A
- Alarm current 8 zones : 0.63 A
- 3 year warranty
- Kentec T11020M2 Fire Control Panels user manuals
- Kentec T11020M2 Fire Control Panels data sheet
£176.19 Inc VAT -
Kentec LA80161M2 Fire Control Panels
- Apollo protocol
- Surface mount
- Non networkable
- 385 x 310 x 90mm
- 3 year warranty
- Kentec LA80161M2 Fire Control Panels data sheet
£413.63 Inc VAT -
Advanced Electronics MX-5201 Fire Control Panels
- 200 Zone Panel (Apollo/Hochiki) with 1 Loop
- Maximum 12Ah internal batteries
- 3 year warranty
- Advanced Electronics MX-5201 Fire Control Panels data sheet
£1,271.09 Inc VAT -
Advanced Electronics MX-5101 Fire Control Panels
- 200 Zone Panel (Apollo/Hochiki)
- Maximum 7Ah internal batteries
- 3 year warranty
- Advanced Electronics MX-5101 Fire Control Panels data sheet
£989.86 Inc VAT -
Kentec K11080M2 Fire Control Panels
- Construction 1.2mm mild sheet steel
- IP Rating IP30
- Finish Epoxy powder coated
- Colour – lid & box BS 00 A 05 grey – fine texture
- Colour – control panel & labels RAL 7047 light grey – satin
- Weight 6kg
- Supply Voltage 230V AC (+10%/-15%)
- Mains supply fuse 1.6 Amp 250V
- Power supply DC rating 24V 3 Amps
- Maximum battery size 7Ah 12V (2 per panel)
- Fault contract rating 30V DC 1 Amp
- Local fire contract rating 30V DC 1 Amp
- Fire contract rating 30V DC 1 Amp
- Common Sounder output rating 0.5A per output (max 1.6A over all outputs)
- AlarmSense Sounder output rating 0.2A per output
- Detection zone current 1.6 milliamps
- Detection zone EOL resistor 3K3 5%
- Sounder output EOL resistor 10k 5%
- Cable capacity 2.5mm² per terminal
- Operating temperature -5°C to +40°C
- Operating humidity <95% (non condensing)
- 3 year warranty
- Kentec user manual
- Kentec K11080M2 Fire Control Panels data sheet
£214.49 Inc VAT